FOR QUESTIONS CONTACT: STEVE [removed phone] or [removed email] 1985 Wellcraft 247 Fisherman (Completely restored in [removed phone]: -Boat- Hull sides from rub-rail to chines-removed all nicks, scratches, etc. from original gel-coat, prepped, then repainted with Imron Paint- 9/1/16 (Americraft Enterprises, Daytona Beach). -Motor- 100hr Service and inspection, replaced Scuppers, re-torque bolts to spec on Bracket (International Marine, Boynton Beach, Fl.)- 5/12/16 -Trailer- Replaced all Calipers with new Kodiaks, New 6-Lug Kodiak Silvercad Slipovers, new -Heavy Duty Winch Strap, New jack, New 24in Brake Line and Brake Fluid, 4 new tires.(Meltra Trailers, Ft. Pierce, Fl)-4/26/[removed phone] -New Custom T-Top built with E-Tech Retractable Outriggers added -Added LED Spreader Lights -Added LED over-head console light bar (Red, white) -Replaced running lights with LED lights -Custom Sunbrella Boat Cover, covers motor and swim platform. Added additional skirt to cover below the chines (sides). (Sunnyland Canvas, Ft. Pierce, Fl.) [removed phone] -Replace and Raise Transom with Full Height Top-Cap -Design and Install Transom Door in Transom, exits on to Armstrong Bracket -Install New Armstrong 72in Wide-Body Bracket with Ladder Mount -Box-In Fuel Filter and Raw-Water Wash-Down Pump Compartment for easy access -Re-Locate Scuppers to Transom VS. Sides of Hull -Added Port and Starboard Bent Butt Rod Holders -Added Electric Plugs on Port and Starboard and 50Amp Breakers -Added Undergunnel LED Lights (Scarab Chris, THT) -Added new 12X12 Performance Lenco Trim Tabs W/Indicator Switches -Filled a few little nicks in the side of hull 2011 -Remove Black Bottom Paint from hull -Re-Gelcoat bottom of hull to new condition/Sand and Buff [removed phone] Repowered with 2008 Suzuki 300hp purchased new in box 7/09, rigged with Fly By Wire controls and digital fuel management gauge. Motor went into commission mid-2010, after all work below was completed. Only 287 Hours. [removed phone] -Re-place Deck Floor, re-core all hatches and bow pulpit- Re-Gelcoat and Non-Skid all non-smooth areas -Remove all carpeting in V-Berth, prep and gelcoat texture web finish -Replace rotted stringers on port and starboard side of fuel-cell, aft. Laminate plywood to -bottom of fuel-cell panel. -Imron paint smooth area of deck-cap and buff non-skid areas -Install new rub-rail kit -6 new Deck Access plates -Replace V-Berth windows -Replace Windshield -Repair old motor holes after repower (twins to single motor) -Remove fuel tank, inspect, clean and pressure check, install all new fuel fill and fuel hoses with USCG Ethanol compliant hoses. -New Leaning Post/Livewell combo, cut-down and fiber-glassed into leaning post, plumbed. (Fab-Tech, Daytona Beach, Fl.) -Removed all wood-trim, including console and v-berth doors, etc. and replaced with non-wood trim/doors. All new latches, etc. -New Sea Star Helm -Completely re-wired Boat and Electronics (ACM Electronics, Jacksonville, Fl.) -Fusion IP600 Head-Unit -(4) 8in Speakers -JBL Marine 4-Channel Marine Amplifier -Lowrance HDS-7 Insight USA 50/200 Transducer -Linked new motor to Lowrance (NMEA 2000 compatible) -Digital VHF and AM/FM Antenna -VHF Radio -Lowrance external GPS and WAAS Antenna -Installed New Gunnel Bolsters and (2) Back Rest Cushions New LoadMaster Trailer -Overbuilt 9800# GVWR Tandem Torsion Axles -(4) Kodiak 12in Silver Cad Plated Disc Brakes -SS Hardware Package -Spare Wheel/Tire Radial -LED Side Marker Lights BOAT LOCATION: Vero Beach, FL (32962)
Engine(s):
Fuel Type: Gas
Engine Type: Other
Quantity: 1
